sctechjobs

Recruitment Not Found

You did not come from a valid link as there is no recruitment number associated with this page request.

Introduction

 

banner

 

In Cooperation with
Trident Technical College

 

is assisting with the recruitment and training for

 

 

AMT Senior Aerospace  

 

 AMT is committed to maintaining world-class standing in high speed machining and structural assembly for the aerospace industry. AMT is a company in which all employees are valued individuals, teamwork is the norm, and continuous improvement is everyone’s personal objective.

Potential employment opportunities exist for:

ASSEMBLER 1

Job Summary: 

The Assembler 1 assembles aerospace structural sections from parts, subassemblies and components.

Education, Skills and Experience:    

 

Required

 

  • Completion of AMT aptitude test during interview process

    

Preferred

 

  • 6 months previous assembly experience in the aerospace industry.
  • Basic shop math skills
  • Ability to read and follow work instructions.
  • G.E.D. or Higher

 

Duties and Responsibilities:

 

  • Installs units, parts, equipment, and components in structural assembly, according to blueprints and specifications, using hand tools and power tools.
  • Bolts, screws, or rivets accessories to fasten, support, or hang components and subassemblies.
  • Drills holes in structure and subassemblies, and attaches brackets, hinges, or clips to secure installation or to fasten subassemblies.
  • Locates and marks reference points and holes for installation of parts and components, using jigs, templates, and measuring instruments.
  • Inspects and tests installed units, parts, and equipment for fit, performance, and compliance with standards, using measuring instruments and test equipment.
  • Positions and aligns subassemblies in jigs or fixtures, using measuring instruments, following blueprint lines and index points.
  • Cuts, trims, and files parts, and verifies fitting tolerances to prepare for installation.
  • Installs bushings using liquid nitrogen or presses as required.
  • Applies sealants or paint per customer specifications using proper safety devices.
  • Uses shop equipment needed to complete operations, such as C-squeeze, arbor presses, ground stud puller, cherry pullers, and shop hand tools.
  • Verifies conformance of finished work piece to specifications using standard measuring tools as required.
  • Reads and interprets manufacturing drawings at intermediate level.
  • Recognizes production problems.
  • Follows 5-S procedures & works in organized manner.
  • Follows all safety guidelines established by the Company, including proper use of safety equipment and relevant safety procedures.
  • Meets job Time Standards with minimal supervision.
  • Produces parts with high quality, minimal non-conformances.

 

 

Required Attributes:

  • Demonstrates a good attitude toward work.
  • Reliable - arrives on time to work with good attendance.
  • Follows instructions and demonstrates strong attention to detail.
  • Communicates well verbally and in writing.
  • Mechanically inclined, with good manual dexterity.

   Physical Demands:

 

  • Lifting up to 40 pounds.
  • Standing, sitting and walking throughout the workday
  • Correctable vision that allows employee to perform accurate assembly work

 

Work Environment:

  • Access to our facility (and, therefore, employment) is restricted under the International Traffic in Arms Regulations (ITAR) and/or Export Administration Regulations (EAR) to U.S. Citizens, lawful permanent residents of the United States and properly licensed foreign persons. Applicants receiving a conditional offer of employment will be required to provide information to determine whether they are subject to these regulations and, if so, to assess their country of chargeability for export control purposes.
  • The Assembly 1 works in the Assembly environment throughout the workday; this environment may include exposure to noise, dust, fumes, etc.
  • Possible skin and inhaled contact may occur with various sealants, paints, adhesives, liquid nitrogen, MEK, and chemicals used during assembly or cleaning of parts.
  • Safety training is required and provided by the Company in accordance with applicable law, industry standards, and Company policy.

Training will be at no charge to trainees.

Successful completion of the training program carries no obligation to accept any offer of employment, nor is an offer guaranteed.

 

 See more at www.readysc.org/amt

 

 

 

 

Computer access and application assistance is available at your local

SCWorks Center.  To locate your nearest center go to http://www.scworks.org/directory.asp

 

An Equal Opportunity Employer

 

 

 




sctechjobs